Equipment Listing:  Due to our extensive Equipment inventory only a partial SMT Equipment List is available. Contact an EXPERT EMS representative for a full listing.

SAMSUNG SM481 High Speed Pick and Place machines:  Advanced High speed Flexible Mounter Pick and Place. Quick-Turn, 40,000 placements with component range including 0201 to 16mm (01005 chip to .65"), placement accuracy 50 microns/chip, 30 microns/QFP, 120 slot feeder capacity for high line item PWA placements, PCB size standard 460mm x 400mm (18.11" x 15.74"), intelligent feeder technology.

SAMSUNG SM482 PNP machines:  Advanced High speed Flexible Mounter Pick and Place. Quick-Turn, 40,000 placements ph with component range including 0201 to 16mm (01005 chip to .65"), placement accuracy 50 microns/chip, 30 microns/QFP, 120 slot feeder capacity for high line item PWA placements,PCB size standard 460mm x 400mm (18.11" x 15.74"),intelligent feeder technology.

Heller 1809 Reflow Ovens:  Forced convection Reflow Oven. 22" wide mesh belt can accommodate up to 20" wide PCB's, 105.0" Heated Tunnel Length, 18 Independent Temp-controlled Zones (9 top, 9 bottom), fully convection-forced hot air heating technology with 350C Blowers,thermocouple profiling, spc data, alarm loging and profile graphing.

SuperM.O.L.E. GOLD with Ovenrider NL 2 ECD Thermal Profiler:  6-Channel measurement and SPC Software. This technology is used to insure integrity in heat ambient and heat transfer of reflow set parameters in Heller Reflow Process. Oven-rider technology is a repeatable fixture that measures oven zone temperatures, checks for consistency in heat transfer (changes in convection), and tracks conveyor speed. Three ambient sensors measure temperature across the width of the pallet looking for deltas or checking lateral uniformity. The process sensors measure heat transfer and will tell you when something is different in the way the air is being circulated by the fans or transferring heat into components/board.

AquaKlean T-15 Cleaner:  Features a 24" belt, Pre-Wash Section includes 2-upper/lower spray bars, heated with 15HP wash pump. Wash Section is heated with 5 upper and 5 lower spray bars with separate 15HP pump. Heated Rinse Section with 5 upper and 5 lower spray bars with separate 15HP pump. Final Rinse Section with DI System including 2 upper and 2 lower spray processes to insure sufficient cleaning of fine pitch QFT and BGA components and DI Water insuring not water spotting on PCB.

KISS-102 Selective Solder:  This automated Selective Soldering Machine with high speed Z axis. Able to process PCB's 16" x 16" (400mm x 400mm) and up to 24" x 18" (600mm x 450mm) with manual step over feature. Integrated I.R. Board Heater sits directly over the board in process and is used to maintain proper pre-solder temperature of board to insure perfect solder joints.

KISS NOVO 102 Selective SolderThis automated Dual Nozzle Selective Soldering Machine with high speed Z axis. Able to process PCB's 16" x 16" (406mm x 406mm) and up to 24" x 18" (600mm x 450mm) with manual step over feature. Integrated I.R. Board Heater sits directly over the board in process and is used to maintain proper pre-solder temperature of board to insure perfect solder joints.

Nordson YESTECH AOI:  Automated Optical Inspection insures Inspection consistency of PWA Assembly Solder/placement/rotation. EXPERT provides AOI on all repeat PWA Assemblies.

Totech Super Dry ESD Moisture Cabinet:  This Super Dry technology insures all moisture sensitive PCB FAB and other moisture-sensitive components (Ball Grid Array) maintain moisture-free integrity during storage. The 5000 Series Dynamic Drying Unit reaches very reliable low Relative Humidity (RH) values of 0.5% RH and automatically regenerates when necessary. Fast drying time for Level 3 components less than 1.4mm=18 hours (60 degrees C/1% RH). This technology has proven to be the safest and most effective at safely reducing moisture in parts and FAB. The alternative approach to bake parts causes excessive oxidation and poor solder quality.

Glenbrook Jewel Box 70-t XRAY:  40kva to 100kva XRAY Inspection for open and solder bridge used in process and in final inspection.

(NEW EQUIPMENT ADDED JANUARY, 2020)

(4) SAMSUNG SM481 High Speed Pick and Place machines

EKRA SERIO 4000 Stencil Printer:  Best in Class Printer utilizing the most advanced user software for fast set up and throughput

PEMTRON SPI: In-line 3D Solder Paste Inspection System

KOH YOUNG SPI in-process SMT Inspection

PVA DELTA 6 Conformal Coating machine with 4-axis robotic platform for dispensing a wide variety of adhesives, sealants, and conformal coatings.  PVA SPECTA UV Curing Oven for fast curing of PC40 coating.  Blacklight Final Inspection workstation at end of line.

Other equipment: Blue M ovens, Nordson epoxy dispensing, Fancort PCB Routers, Olamef Counter, various Materials Management technology.

At EXPERT we strive to maintain all the current technology to improve Quality and On-Time Delivery at the most competitive price to our Customers.

Find out why EXPERT has been the EMS Provider of Choice to over 100 OEM Companies.

When you want the best partner for Materials and Assembly go directly to the EXPERTs.

EXPERT-EMS, your Vision is our Mission.